Bitemporal-to-Bizygomatic Width
The width of the forehead at the temples as a percentage of the face width across the cheekbones.
- Formula
- Forehead width at the temples ÷ face width at the cheekbones × 100
- Unit
- Percent (%)
- Photo
- Front view
How it is measured
- Front view: pick a level halfway between the brows and the hairline.
- At that level, find where skin meets hair on each side; these are the temple points.
- Divide the temple-to-temple width by the cheek-to-cheek width and multiply by 100.
Reading the value
- Lower
- The forehead is clearly narrower than the cheeks.
- Higher
- The forehead nears, or exceeds, the width of the cheeks.
Why it matters
The value describes how the upper face tapers into the cheeks. Two faces with the same cheek width can differ markedly in forehead width. Temple width reflects bone, the temporal muscle and where the side hairline runs.
Limits
Side hair, a fringe or a hat over the temples moves or blocks the temple points; without a clear skin-to-hair edge an estimate is used. The value describes the visible forehead, not bone under hair. A turned head changes both widths.
Use a level, directly front-facing photo with even light. Head rotation, expression, hair or shadows can hide or shift the points. A measurement describes a photo, not a diagnosis, and no single value is good or bad on its own.
Video guide
Research
- Temple filler: how much stays after 6 months, seen on ultrasoundPlast Reconstr Surg Glob Open · 2024 · cohort study · Moderate evidence
Measured filler volume was 0.86 mL at 3 months and 0.72 mL at 6 months; temple depression went from 4.33 mm to 0.71 mm (3 months) and 1.62 mm (6 months), with grade improvements of 2.41 and 1.74.
- A layered filler technique for hollow templesFront Surg · 2025 · case series · Limited evidence
Volumising and lifting effects in the upper face were reported in all patients; 15 had mild and 2 moderate pain, with no serious events or bruising collections.
- Facial features targeted in gender-affirming aesthetic treatmentDermatol Surg · 2024 · narrative review · Limited evidence
Masculine faces are described as more rectangular, with temple, cheekbone and jaw-angle widths close to 1:1:1, and feminine faces as heart-shaped with more cheekbone projection and a tapering jawline; the position of the cheek high point is highlighted as key.
- Temple anatomy and how temple filler is injectedSurg Radiol Anat · 2024 · narrative review · Limited evidence
Hollow temples tend to deepen with age. Filler is placed either between fascia layers with a blunt cannula or deep on the bone with a needle, and the review details where arteries and veins run to reduce the risk of vessel injury.
- Expert guide to fillers and botulinum toxin in the upper facePlast Reconstr Surg · 2017 · expert view · Limited evidence
The authors stress slow injection and knowledge of vessels and nerves to avoid complications. Botulinum toxin is suggested for forehead, frown and crow's feet lines and for brow lifting; fillers for temples, brows and forehead.
- Reshaping the temples and cheekbones through a scalp incisionClin Plast Surg · 1991 · technique report · Limited evidence
The author recommends assessing temples, cheekbone arch and midface together, placing a 3 to 4 mm implant under the temple muscle and burring down the arch to the desired thinness.
These studies describe the feature or how it is measured. They do not show that one value is better than another.
Procedures that change it
- Cheekbone reduction+4.6 % in the simulated example on the reference face
- Cheek implants-3.9 % in the simulated example on the reference face
- Temple filler+2.7 % in the simulated example on the reference face
- Cheek filler-1.7 % in the simulated example on the reference face
Each example uses the app’s starting strength on one reference face; on another face the same procedure moves this value by another amount.
Measure your bitemporal-to-bizygomatic width – freeMeasured in your browser. Your scans are saved on your device.